AS 1101.3-2005 Graphical symbols for general engineering - Welding and non-destructive examination
|
ID： |
09DD993E3C7B4B589C606B9C3D030071 |
|
文件大小(MB)： |
2.31 |
|
页数： |
121 |
|
文件格式： |
|
|
日期： |
2009-4-15 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
AS 1101.3—2005,Australian Standard.,Graphical symbols for general,engineering,Part 3: Welding and non-destructive,examination,AS 1101.3—2005,Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 02 Dec 2006,This Australian Standard was prepared by Committee WD-001, Welding Definitions,and Symbols. It was approved on behalf of the Council of Standards Australia on,25 November 2004.,This Standard was published on 31 March 2005.,The following are represented on Committee WD-001:,Australian Industry Group,Bureau of Steel Manufacturers of Australia,New Zealand Heavy Engineering Research Association,Welding Technology Institute of Australia,Keeping Standards up-to-date,Standards are living documents which reflect progress in science, technology and,systems. To maintain their currency, all Standards are periodically reviewed, and,new editions are published. Between editions, amendments may be issued.,Standards may also be withdrawn. It is important that readers assure themselves,they are using a current Standard, which should include any amendments which,may have been published since the Standard was purchased.,Detailed information about Standards can be found by visiting the Standards Web,Shop at www.standards.com.au and looking up the relevant Standard in the on-line,catalogue.,Alternatively, the printed Catalogue provides information current at 1 January each,year, and the monthly magazine, The Global Standard, has a full listing of revisions,and amendments published each month.,Australian StandardsTM and other products and services developed by Standards,Australia are published and distributed under contract by SAI Global, which,operates the Standards Web Shop.,We also welcome suggestions for improvement in our Standards, and especially,encourage readers to notify us immediately of any apparent inaccuracies or,ambiguities. Contact us via email at mail@standards.org.au, or write to the Chief,Executive, Standards Australia, GPO Box 5420, Sydney, NSW 2001.,This Standard was issued in draft form for comment as DR 04480.,Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 02 Dec 2006,AS 1101.3—2005,Australian Standard.,Graphical symbols for general,engineering,Part 3: Welding and non-destructive,examination,Originated as AS Z6—1955.,Previous edition AS 1101.3—1987.,Third edition 2005.,COPYRIGHT,. Standards Australia,All rights are reserved. No part of this work may be reproduced or copied in any form or by,any means, electronic or mechanical, including photocopying, without the written,permission of the publisher.,Published by Standards Australia GPO Box 5420, Sydney, NSW 2001, Australia,ISBN 0 7337 6555 6,Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 02 Dec 2006,AS 1101.3—2005 2,PREFACE,This Standard was prepared by the Joint Standards Australia/Standards New Zealand,Committee WD-001, Welding Definitions and Symbols, to supersede AS 1101.3—1987.,The 1987 edition of the Standard was generally based on ANSI/AWS A2.4-79, Symbols for,Welding and Non-destructive Testing, and the permission of the American Welding Society,Inc. to use their Standard was acknowledged.,This edition continues to follow the ANSI/AWS A2.4, and takes cognizance of its 1998,edition.,The main changes in this edition include—,(a) the use of a new symbol for edge weld to replace the symbols for flange edge and,corner welds (see Section 6); and,(b) the introduction of a symbol for stud weld (see Section 11).,In addition, the format of the Standard has been changed and editorial changes have been,included in line with current Standards Australia policy.,The Standard provides a scheme whereby complete details of welds and welded joints can,be delineated on drawings. A separate section covers symbols for use on drawings to,specify requirements for non-destructive examination for determining the soundness of,materials.,The method for symbolic representation of welds on engineering drawings used in this,standard is consistent with the ‘third angle’ method of projection, which is the preferred,method given in AS 1100, Technical drawing, Part 101: General principles. It should be,noted, however, that the scheme is equally appropriate to drawings in which the ‘first angle’,method of projection is used.,The committee noted the practice currently adopted in ISO 2553, Welded, brazed and,soldered joints; symbolic representation on drawings, in regard to the position of the,symbols on drawings, viz., the dual reference line, and felt that this situation should not be,carried over into this Standard. Therefore, the practice of using one continuous reference,line remains unaltered in this edition.,Illustrations used with the text are intended onl……
……